In situ optical sub-wavelength thickness control of porous anodic aluminum oxide

• Aleksandrs Dutovs,
• Raimonds Popļausks,
• Oskars Putāns,
• Vladislavs Perkanuks,
• Aušrinė Jurkevičiūtė,
• Tomas Tamulevičius,
• Uldis Malinovskis,
• Iryna Olyshevets,
• Donats Erts and
• Juris Prikulis

Beilstein J. Nanotechnol. 2024, 15, 126–133, doi:10.3762/bjnano.15.12

• zinc oxide nanorods embedded within the PAAO template [13]. Recently, it was demonstrated that the PAAO thickness tuning can increase the signal intensity and refractometric sensitivity of localized surface plasmon resonance (LSPR) sensors constructed using gold nanoparticles, which are deposited on

Assessing phytotoxicity and tolerance levels of ZnO nanoparticles on Raphanus sativus: implications for widespread adoptions

• Pathirannahalage Sahan Samuditha,
• Nadeesh Madusanka Adassooriya and
• Nazeera Salim

Beilstein J. Nanotechnol. 2024, 15, 115–125, doi:10.3762/bjnano.15.11

• Lanka 10.3762/bjnano.15.11 Abstract The escalating release of zinc oxide nanoparticles (ZnO NPs) into the environment poses a substantial threat, potentially leading to increased concentrations of zinc (Zn) in the soil and subsequent phytotoxic effects. This study aimed to assess the effects of ZnO NPs

• , which may be top-down or bottom-up approaches, has facilitated the synthesis of nanoparticles of differing shapes, sizes and properties [11]. When considering zinc oxide nanoparticles (ZnO NPs) in particular, their low toxicity, high biocompatibility, and low cost [12] have enabled them to be applied as

• synthase, an enzyme responsible for the synthesis of tryptophan in the biosynthesis of IAA [36][37]. According to the present results, ZnO NPs have no toxic effect on IAA content at 1000 mg/L; however, it increased the IAA content at 2000 mg/L. Zinc oxide NPs are a potential candidate to enhance the

A visible-light photodetector based on heterojunctions between CuO nanoparticles and ZnO nanorods

• Doan Nhat Giang,
• Nhat Minh Nguyen,
• Duc Anh Ngo,
• Thanh Trang Tran,
• Le Thai Duy,
• Cong Khanh Tran,
• Thi Thanh Van Tran,
• Phan Phuong Ha La and
• Vinh Quang Dang

Beilstein J. Nanotechnol. 2023, 14, 1018–1027, doi:10.3762/bjnano.14.84

• ][18]. Semiconductors are the heart of photodetectors as their bandgap allows for the absorption of photons in the desired wavelength range [19]. There are many semiconductor materials developed for this application. Among them, zinc oxide (ZnO) has been studied extensively over the last decades

• studied and optimized to achieve higher performance and to reduce response and decay times in the future. Experimental Materials The chemical materials used in this report were zinc oxide nanoparticles (ZnO NPs, 99%, Sigma-Aldrich Chemistry), hexamethylenetetramine (HTMA, 99%, C6H12N4, Xilong Scientific

A wearable nanoscale heart sound sensor based on P(VDF-TrFE)/ZnO/GR and its application in cardiac disease detection

• Yi Luo,
• Jian Liu,
• Jiachang Zhang,
• Yu Xiao,
• Ying Wu and
• Zhidong Zhao

Beilstein J. Nanotechnol. 2023, 14, 819–833, doi:10.3762/bjnano.14.67

• flexible piezoelectric thin film heart sound sensor was developed, and a heart sound detection and classification system was built based on this sensor. Zinc oxide (ZnO) and graphene (GR) fillers were added to the P(VDF-TrFE) matrix, and P(VDF-TrFE)/ZnO/GR composite piezoelectric nanofilms were prepared

ZnO-decorated SiC@C hybrids with strong electromagnetic absorption

• Liqun Duan,
• Zhiqian Yang,
• Yilu Xia,
• Xiaoqing Dai,
• Jian’an Wu and
• Minqian Sun

Beilstein J. Nanotechnol. 2023, 14, 565–573, doi:10.3762/bjnano.14.47

• materials due to their high content of surface functional groups. Among dielectric materials, zinc oxide possesses the outstanding characteristics of low cost, non-toxicity, excellent thermodynamic stability and photostability, and unique semiconducting properties. Hence, it is widely used in the fields of

Batch preparation of nanofibers containing nanoparticles by an electrospinning device with multiple air inlets

• Dong Wei,
• Chengwei Ye,
• Adnan Ahmed and
• Lan Xu

Beilstein J. Nanotechnol. 2023, 14, 141–150, doi:10.3762/bjnano.14.15

• addition, experiments and theoretical analysis were used to discuss the spinning mechanism of this new device for the batch preparation of nanofibers, and the optimal spinning parameters were determined. Materials and Methods Materials Polyacrylonitrile (PAN, average molecular weight 15000) and zinc oxide

Antimicrobial and mechanical properties of functionalized textile by nanoarchitectured photoinduced Ag@polymer coating

• Jessica Plé,
• Marine Dabert,
• Helene Lecoq,
• Sophie Hellé,
• Lydie Ploux and
• Lavinia Balan

Beilstein J. Nanotechnol. 2023, 14, 95–109, doi:10.3762/bjnano.14.11

• [10]), gold [11][12], zinc oxide [13][14], and especially silver nanoparticles [15][16][17][18]. Silver is known to target peptidoglycane, a cellular membrane component of Gram-negative and -positive bacteria. If introduced directly in its ionic form, silver interacts with the electron-donor groups of

Hydroxyapatite–bioglass nanocomposites: Structural, mechanical, and biological aspects

• Olga Shikimaka,
• Mihaela Bivol,
• Bogdan A. Sava,
• Marius Dumitru,
• Christu Tardei,
• Beatrice G. Sbarcea,
• Daria Grabco,
• Constantin Pyrtsac,
• Daria Topal,
• Andrian Prisacaru,
• Vitalie Cobzac and
• Viorel Nacu

Beilstein J. Nanotechnol. 2022, 13, 1490–1504, doi:10.3762/bjnano.13.123

• by an unconventional wet route followed by melting [31][37][38]. As raw materials, the ultra-purity grade reagents boron oxide (B2O3), magnesium oxide (MgO,) potassium carbonate (K2CO3), phosphoric acid (H3PO4), silicon dioxide (SiO2), zinc oxide (ZnO), and cerium oxide (CeO2) have been used. The

Green synthesis of zinc oxide nanoparticles toward highly efficient photocatalysis and antibacterial application

• Vo Thi Thu Nhu,
• Nguyen Duy Dat,
• Le-Minh Tam and
• Nguyen Hoang Phuong

Beilstein J. Nanotechnol. 2022, 13, 1108–1119, doi:10.3762/bjnano.13.94

• , Vietnam 10.3762/bjnano.13.94 Abstract Zinc oxide nanoparticles (ZnO NPs) were successfully synthesized by a green method using rosin and zinc chloride as salt precursors. The phase structure, morphology, and particle size of ZnO were determined by X-ray powder diffraction, field emission scanning

• (0.06 µS/cm). Escherichia coli (E. coli VTCC-B-482) was used for the antibacterial experiments and purchased from the Hanoi National University. Preparation of zinc oxide nanoparticles by green syntheses The ZnO NPs were synthesized by two steps. Firstly, the saponification reaction of rosin was

• almost completely decomposed and only the zinc metal is oxidized to form zinc oxide. The XRD diagram of ZnO samples (Figure 3) shows diffraction peaks located at 2θ = 31.81°; 34.44°, 36.26°, 47.57°, 56.64°, 62.88°, 66.41°, 67.96°, 69.12°, 72.72°, 77.01° corresponding to the crystal planes (100), (002

Biomimetic chitosan with biocomposite nanomaterials for bone tissue repair and regeneration

• Se-Kwon Kim,
• Sesha Subramanian Murugan,
• Pandurang Appana Dalavi,
• Sebanti Gupta,
• Sukumaran Anil,
• Gi Hun Seong and
• Jayachandran Venkatesan

Beilstein J. Nanotechnol. 2022, 13, 1051–1067, doi:10.3762/bjnano.13.92

• , researchers have tried several ways to develop different materials using chitosan-based nanocomposites of silver, copper, gold, zinc oxide, titanium oxide, carbon nanotubes, graphene oxide, and biosilica. The combination of materials helps in the expression of ideal bone formation genes of alkaline

• oxide, zinc oxide, carbon nanotubes, graphene oxide, and biosilica was developed to improve bone scaffolds for better bone tissue repair and regeneration [11]. In tissue engineering applications, nanoscale topological characteristics influence cell adhesion, survival, proliferation, and differentiation

• and regeneration [14]. Nanomaterials such as silver [15], gold [16][17], titanium oxide [18], zinc oxide [19][20], carbon nanotubes [21][22], graphene [23] and biosilica have been studied in terms of their osteogenic potential in stem cell differentiation. Chitosan materials are often combined with

Zinc oxide nanostructures for fluorescence and Raman signal enhancement: a review

• Ioana Marica,
• Fran Nekvapil,
• Maria Ștefan,
• Cosmin Farcău and
• Alexandra Falamaș

Beilstein J. Nanotechnol. 2022, 13, 472–490, doi:10.3762/bjnano.13.40

• applications [13]. This review article seeks to present the fabrication methods and applications of zinc oxide nanostructures enhancing the photoluminescence emission or the Raman signal of analyte molecules. First, we focus on a wide range of synthesis methods of ZnO nanostructures and nanocomposites based on

• candidates for recombination centres involved in the visible luminescence of ZnO [77][79]. Thus, the electrical and luminescence characteristics of zinc oxide could be changed by the number of oxygen vacancies or other point defects (vacancies, atom substitutions, and interstitial atoms). Moreover

• also benefits the SERS enhancement. Doping zinc oxide–Ag nanoparticles with magnesium also introduces defect sites (surface defects and oxygen vacancies), which form new energy levels below the conduction band of zinc oxide, facilitating the charge transfer mechanism. In this case, besides the charge

A chemiresistive sensor array based on polyaniline nanocomposites and machine learning classification

• Jiri Kroutil,
• Alexandr Laposa,
• Ali Ahmad,
• Jan Voves,
• Vojtech Povolny,
• Ladislav Klimsa,
• Marina Davydova and
• Miroslav Husak

Beilstein J. Nanotechnol. 2022, 13, 411–423, doi:10.3762/bjnano.13.34

• mg additives (zinc oxide, two forms of tungsten oxide, indium oxide, fullerene, NCD, and barium titanate) in 2 mL xylene. Table 3 shows properties of the used additives. The prepared solutions were mixed in a shaker for 30 min and subsequently ultrasonicated for 30 min. Finally, the obtained

Selected properties of Al_xZn_yO thin films prepared by reactive pulsed magnetron sputtering using a two-element Zn/Al target

• Witold Posadowski,
• Artur Wiatrowski,
• Jarosław Domaradzki and
• Michał Mazur

Beilstein J. Nanotechnol. 2022, 13, 344–354, doi:10.3762/bjnano.13.29

• : aluminium zinc oxide; magnetron sputtering; thin film; transparent conducting oxide; transparent electronics; Introduction Aluminium-doped zinc oxide (AZO) is a potential alternative to indium tin oxide (ITO) for transparent conducting oxide (TCO) electrodes in transparent electronic and photovoltaic

• many preliminary experiments to find optimum conditions for the deposition of thin films with desired properties. For the deposition of AZO thin films by magnetron sputtering, the most commonly used targets are made of sintered zinc oxide powders and aluminum oxide (ZnO/Al2O3). The optimal percentage

Identifying diverse metal oxide nanomaterials with lethal effects on embryonic zebrafish using machine learning

• Richard Liam Marchese Robinson,
• Haralambos Sarimveis,
• Philip Doganis,
• Xiaodong Jia,
• Marianna Kotzabasaki,
• Christiana Gousiadou,
• Stacey Lynn Harper and
• Terry Wilkins

Beilstein J. Nanotechnol. 2021, 12, 1297–1325, doi:10.3762/bjnano.12.97

• . This is restrictive, as generalization for nanomaterials with similar but non-identical chemical compositions is not possible. Subsequent studies only developed local models for ENMs with nominally the same core material, for instance, gold or zinc oxide, where only the variation in the chemical

Enhancement of the piezoelectric coefficient in PVDF-TrFe/CoFe₂O₄ nanocomposites through DC magnetic poling

• Marco Fortunato,
• Alessio Tamburrano,
• Maria Paola Bracciale,
• Maria Laura Santarelli and
• Maria Sabrina Sarto

Beilstein J. Nanotechnol. 2021, 12, 1262–1270, doi:10.3762/bjnano.12.93

• with zinc oxide nanostructures [1][3][5][6]. Recently, it was shown that the β phase content of PVDF can be improved introducing CoFe2O4 nanoparticles into the polymer and applying a DC magnetic field [25]. This effect has been ascribed to the strong tensile stress at the CoFe2O4/PVDF interfaces

Morphology-driven gas sensing by fabricated fractals: A review

• Vishal Kamathe and
• Rupali Nagar

Beilstein J. Nanotechnol. 2021, 12, 1187–1208, doi:10.3762/bjnano.12.88

• . The response of sensor was described by the real and imaginary parts of the reflection coefficient using a specific waveguide. The response was found to be linear for ammonia in the range of 0–500 ppm. Zinc oxide-based fractals Hierarchical dandelion-like hollow ZnO structures were reported by Fan et

The role of deep eutectic solvents and carrageenan in synthesizing biocompatible anisotropic metal nanoparticles

• Nabojit Das,
• Akash Kumar and
• Raja Gopal Rayavarapu

Beilstein J. Nanotechnol. 2021, 12, 924–938, doi:10.3762/bjnano.12.69

• successful use in biological milieus. Recent studies indicated that the green synthesis of nanoparticles, such as zinc oxide nanoparticles and bimetallic copper–silver and nickel–cobalt nanoparticles, is preferred for catalytic, antibacterial, and therapeutic applications [12][13][14]. Several other

9.1% efficient zinc oxide/silicon solar cells on a 50 μm thick Si absorber

• Rafal Pietruszka,
• Bartlomiej S. Witkowski,
• Monika Ozga,
• Katarzyna Gwozdz,
• Ewa Placzek-Popko and
• Marek Godlewski

Beilstein J. Nanotechnol. 2021, 12, 766–774, doi:10.3762/bjnano.12.60

• using zinc oxide nanorods. The efficiency of a textured solar cell structure is compared with the one obtained for a planar zinc oxide/silicon structure. The present results show the possibility to produce efficient solar cells on a relatively thin 50 μm thick silicon substrate. Solar cells with

• structured top electrodes were examined by numerous measuring techniques. Scanning electron microscopy revealed a grain-like morphology of the magnesium-doped zinc oxide film. The size of the grains is closely related to the structure of the nanorods. The external quantum efficiency of the cells was measured

• % for planar structures, respectively. The work, therefore, describes an environmentally friendly technology for PV architecture with surface textures increasing the efficiency of PV cells. Keywords: atomic layer deposition; hydrothermal method; photovoltaics; silicon; solar cell; zinc oxide

A review of defect engineering, ion implantation, and nanofabrication using the helium ion microscope

• Frances I. Allen

Beilstein J. Nanotechnol. 2021, 12, 633–664, doi:10.3762/bjnano.12.52

• by localized helium ion irradiation. For example, using a helium ion dose of 5 × 1014 ions/cm2, permanent local tuning of the charge density in an amorphous thin film of the semiconductor indium gallium zinc oxide (film thickness 50 nm) has been demonstrated, thereby enabling activation of the

Impact of GaAs(100) surface preparation on EQE of AZO/Al₂O₃/p-GaAs photovoltaic structures

• Piotr Caban,
• Rafał Pietruszka,
• Jarosław Kaszewski,
• Monika Ożga,
• Bartłomiej S. Witkowski,
• Krzysztof Kopalko,
• Piotr Kuźmiuk,
• Katarzyna Gwóźdź,
• Ewa Płaczek-Popko,
• Krystyna Lawniczak-Jablonska and
• Marek Godlewski

Beilstein J. Nanotechnol. 2021, 12, 578–592, doi:10.3762/bjnano.12.48

• ; gallium arsenide; photovoltaics; surface passivation; Introduction The atomic layer deposition (ALD) method is used for silicon passivation in photovoltaics. In recent years we proposed the usage of ALD for the construction of simplified Si-based cells [1]. Once zinc oxide (ZnO) nanorods were employed as

• for aluminum-doped zinc oxide). Experimental GaAs surface treatment We used lightly Zn-doped GaAs single-crystal (100) wafer (p = 6.8 × 1016 cm−3, ρ = 3.2 × 10−1 Ω·cm, μ ≤ 225 cm2/Vs, d = 400 μm) (fabricated at the Institute of Electronic Materials Technology, ITME) as the substrate. Before starting

• -cycles. Each multi-cycle, in turn, consisted of one aluminum oxide creation cycle (TMA + H2O) and 24 cycles of zinc oxide deposition (diethylzinc/Zn(C2H5)2, DEZ, CAS:557-20-0) + H2O [2]. In the final fabrication process, a top point contact was deposited (70 nm) by aluminum-target sputtering (Kurt J

Structural and optical characteristics determined by the sputtering deposition conditions of oxide thin films

• Petronela Prepelita,
• Florin Garoi and
• Valentin Craciun

Beilstein J. Nanotechnol. 2021, 12, 354–365, doi:10.3762/bjnano.12.29

• dioxide (SiO2) and zinc oxide (ZnO) thin films deposited by radio frequency magnetron sputtering on quartz substrates was investigated. The deposition conditions were optimized to achieve stoichiometric thin films. The orientation of crystallites, structure, and composition were investigated by X-ray

A review on the biological effects of nanomaterials on silkworm (Bombyx mori)

• Sandra Senyo Fometu,
• Guohua Wu,
• Lin Ma and
• Joan Shine Davids

Beilstein J. Nanotechnol. 2021, 12, 190–202, doi:10.3762/bjnano.12.15

• to generate more reactive oxygen species (ROS) and to induce oxidative stress could be a reason for their antibacterial activity against R. solanacearum in tobacco plants [23]. Aside from MgO NPs, other nanomaterials, including titanium dioxide (TiO2 NPs), zinc oxide (ZnO NPs), copper oxide (CuO NPs

• [37] and chemicals, and to evaluate nano–bio interactions. The exposure of nanomaterials (NM) to the environment is reported to have detrimental effects on human lungs. Pulmonary inflammation was reported in C57BL/6N mice exposed to zinc oxide (ZnO) (size of nanoparticles functionalized with

ZnO and MXenes as electrode materials for supercapacitor devices

• Ameen Uddin Ammar,
• Ipek Deniz Yildirim,
• Feray Bakan and
• Emre Erdem

Beilstein J. Nanotechnol. 2021, 12, 49–57, doi:10.3762/bjnano.12.4

• materials; electrodes; MXenes; supercapacitors; zinc oxide (ZnO); Introduction In this article, the past, the present, and the prospects of ZnO and MXenes are discussed in terms of their usage as electrode materials in supercapacitor devices. Recently, supercapacitors gained a lot of attention due to their

• and 3D materials will be of utmost benefit to the interested community. Review ZnO as electrode material for supercapacitors Zinc oxide (ZnO) is a highly defective semiconductor material, regardless of its synthesis route, that has a large bandgap energy (Eg) at room temperature. However, defect types

Antimicrobial metal-based nanoparticles: a review on their synthesis, types and antimicrobial action

• Matías Guerrero Correa,
• Fernanda B. Martínez,
• Cristian Patiño Vidal,
• Camilo Streitt,
• Juan Escrig and
• Carol Lopez de Dicastillo

Beilstein J. Nanotechnol. 2020, 11, 1450–1469, doi:10.3762/bjnano.11.129

• -based NPs have demonstrated antimicrobial activity over the last years. Several metal and metal oxide NPs, such as silver, copper, zinc oxide, titanium oxide, copper oxide, and nickel oxide NPs, are known to display antimicrobial activity [15][16][17] that depends on their composition, surface

• nanomaterials which have also presented relevant antimicrobial properties against several pathogenic microorganisms. Zinc oxide, titanium dioxide, copper oxide, and nickel oxide are the most typical metal-oxide NPs with potential antibacterial, antifungal and antiviral activities [127][128]. These oxides have

• ]. Silver, gold, zinc oxide, and titanium dioxide NPs can be attracted to the cell wall by electrostatic attraction [161], van der Waals forces [162], and hydrophobic interactions [163], inducing changes in the shape, function and permeability of the cells. Proteins and DNA Proteins play a fundamental role

Gram-scale synthesis of splat-shaped Ag–TiO₂ nanocomposites for enhanced antimicrobial properties

• Mohammad Jaber,
• Asim Mushtaq,
• Kebiao Zhang,
• Jindan Wu,
• Dandan Luo,
• Zihan Yi,
• M. Zubair Iqbal and
• Xiangdong Kong

Beilstein J. Nanotechnol. 2020, 11, 1119–1125, doi:10.3762/bjnano.11.96

• , silver (Ag), zinc oxide (ZnO), copper oxide (CuO), iron oxide (Fe3O4) and titanium oxide (TiO2) are well recognized options due to their outstanding antibacterial properties. These nanoparticles have antibacterial activity due to the production of reactive oxygen species (ROS) [9][10][11]; more